My home network was configured with the cable modem in bridge mode to which I attached my Asus RT-AC87R router. Wired devices were connected to switches that were connected to the Asus router. Several devices (like our NAS server) had static IPs. Following the Uverse installation, much of this stopped working.

Due to a petty argument with his girlfriend..I overheard her and her friend and discovered that she had logged into the Uverse router/modem (192.168.1.254), which shows all devices that are connected. Setup the Uverse Modem/Router Turn off the wireless network Settings > LAN > Wireless > Wireless Interface > Disabled; Verify your Apple Airport is the only thing using your Uverse Modem's Router Settings > LAN > Status; Devices > Clear List; You want to only see one device. Set Airport in the Uverse DMZ Settings > LAN > IP Address Allocation May 17, 2020 · It will help you to get back to the initial settings if you are facing problems. Conclusion If you are facing problems with your AT&T Uverse Router, it is a great thing to completely reset the AT&T Router and then configure again. Hi Everyone, I would like to basically turn off all the firewall features or open up the router to the modem, so the only firewall in place is the Uverse gateway’s, I was considering using the DMZ for all the IPs, but I am not sure if that is the correct way, what is the best way to do such thing Apr 09, 2019 · Use an Ethernet cable to connect the computer to any of the LAN ports as shown in the diagram. Connect the NETGEAR DSL modem router to its power supply unit (PSU) (Not shown in the diagram) and wait about a minute for it to boot up. Note: If you have an existing DSL modem or modem router, please remove it from your network. Select the settings Tab and then select Firewall. Under Option 1 ‘Select a Computer’ review the list of devices. Your IP phone has a MAC address label. look for that label on the bottom of your phone. Compare that number with the device numbers on the Uverse list (above) When you find the matching number, select it.

Aug 18, 2013 · AT&T doesn’t provide much support for people using their own equipment, leaving it up to us to figure out configuration issues. They now support IPv6. The following instructions for an ASUS router (most use the same software) are derived from the information at: IPv6 compatibility for IFITL page hosted by AT&T. My setup uses DSL, not IFITL, and is across the country from the area referred to

When you sign up for AT&T U-verse Internet service, you receive a wireless gateway that acts as both modem and router. The device comes pre-programmed so that you can connect and start surfing This category features a list of several AT&T U-Verse Modems that are DSL compatible with ATT service. This is based on providers approved list, but it is important that you always check with your provider to ensure compatibility with any provider. To tweak the settings, you first need to access or log in to the router. The process of logging in to the router, while not a robust bridge to cross, can leave a few brains smoking. Don’t fret my friend! Today we have broken down the process login into at&t U-Verse Router in simple bite-sized steps in this guide.

Forum discussion: Got a UVerse INID install today with a I38HG modem. Need some help, and I'm calling in the big guns to help me out. I have a D-Link DIR-655 and want to put that router behind the

Uverse TV/Direct TV uses IP Multicast, which Netgear doesn't handle well. Don't use the Uverse Wi-Fi networks for your main devices. OTOH, you can use them as an isolated network for guests or IoT devices. Set up the Orbi as an Access Point (AP) by enabling AP under Advanced Settings. The Uverse gateway will continue to operate as your main router. Aug 18, 2013 · AT&T doesn’t provide much support for people using their own equipment, leaving it up to us to figure out configuration issues. They now support IPv6. The following instructions for an ASUS router (most use the same software) are derived from the information at: IPv6 compatibility for IFITL page hosted by AT&T. My setup uses DSL, not IFITL, and is across the country from the area referred to You also need to change your LAN IP scheme on the Uverse modem to 172.16.0.1 with yours (Settings, LAN, DHCP). Log into modem also, click settings, Event Notifications, check router behind router detection. Your WiFi will not work if you do this. Just spent 3 hours the other day finally connecting a Asus AC66R behind my Uverse crappy B/G. Page 1: Get Started AT&T U-verse ® Wireless TV Receiver self- installation guide Get started Approximate installation time: 20 minutes These instructions will guide you through the process of installing your AT&T U-verse Wireless TV Receiver. dustman81 writes: AT&T Uverse modems were found to have several serious vulnerabilities, including a superuser account with hardcoded username/password exposed to the internet via SSH, a HTTP server with little authentication which allows command injection, and an internet exposed service which Aug 07, 2014 · From the gateway, navigate to: Settings > Firewall > Applications, Pinholes and DMZ. Choose the router from the list. It will appear as a link named “Choose .” Change its setting below to “Allow all applications (DMZplus mode).” Assigning a public IP. Finally, we need to give the router the knowledge that it’s a public-facing · Only use the Ethernet port on the modem. If you were using the USB connection before using the router, disconnect the USB cable and connect an Ethernet cable to the WAN port of the router. If you were using the USB connection before using the router, disconnect the USB cable and connect an Ethernet cable to the WAN port of the router.